PIR Occupancy Sensors

The Echo PIR Occupancy Sensor is a ceiling-mounted sensor that utilizes passive infrared (PIR) technology, providing reliable occupancy and vacancy detection for lighting control. These sensors provide both automatic on and automatic off functionality working in conjunction with commands from local stations. The PIR Occupancy Sensor provides 360 degree coverage of the installed location and is available in the following models:

Echo PIR Occupancy Sensor	Coverage
E-OCC-SR	Small room lens	450 ft² at 8 ft (42 m² at 2.4 m) 800 ft² at 12 ft (74.3 m² at 3 m)
E-OCC	Standard room lens	1,800 ft² at 8 ft (167 m² at 2.4 m) 3,000 ft² at 10 ft (279 m² at 3 m)
E-OCC-HC	High ceiling lens	350 ft² at 10 ft (32.5 m² at 3 m) 7,000 ft² at 40 ft (650 m² at 12 m)

Echo PIR Occupancy Sensor

Coverage

E-OCC-SR

Small room lens

450 ft² at 8 ft (42 m² at 2.4 m)

800 ft² at 12 ft (74.3 m² at 3 m)

E-OCC

Standard room lens

1,800 ft² at 8 ft (167 m² at 2.4 m)

3,000 ft² at 10 ft (279 m² at 3 m)

E-OCC-HC

High ceiling lens

350 ft² at 10 ft (32.5 m² at 3 m)

7,000 ft² at 40 ft (650 m² at 12 m)

Reference the Unison Echo Occupancy Sensor Installation Guide for information on installing this sensor. All ETC documentation is available for free download from etcconnect.com.

Configuring the Occupancy Sensor

Use the drop-down menus and keypad to set the configurable features. Additional menu options will display based on the Action selected (e.g., if the Vacancy Sensor Event Action is set to Preset Active, Preset Number and Timing (in seconds) displays for specification). The Multi Space Enable switch will display if the Vacancy Sensor Event Action is set to Preset Activate or Space Off and Occupancy Sensor Event Action is set to Preset Activate, allowing you to choose multiple spaces to which these actions will be applied.

Note: Changes made to the PIR Occupancy Sensor configuration settings using the EchoAccess App impact the behavior of the sensor when Custom Config mode has been enabled (set to On). The Custom Config mode DIP switch is located on the circuit board (rear side) of the sensor. A sensor placed in Basic Config mode (Custom Config DIP switch set to Off) is unaffected by EchoAccess App custom configuration settings.

Vacancy Timeout - use the drop-down menu to set the length of time the sensor waits before triggering the next action. Options include 5 minutes, 15 minutes, 30 minutes, and Automatic.
Current Status (read-only) - displays the current status (either Vacant or Occupied) of the Space controlled by the sensor.
Enable Detection LEDs - use the toggle switch to enable or disable the red detection LEDs. If enabled and occupancy is detected, the detection LEDs illuminate with each detected occupancy motion.
Walktest Activated - use the toggle switch to enable or disable the sensor's walktest feature. When walktest is enabled, physically walking through the space confirms the functional sensor range, illuminating the PIR LED with each detected occupancy motion.
Vacancy Sensor Event - use the drop-down menu to set the event Action that will take place when vacancy is detected. Additional menu options will display based on the Action selected (e.g., if the Action is set to Preset Active, Preset Number and Timing (in seconds) displays for specification).
- Available actions includeNo Function, Preset Activate, Zone Set to Level, Space Off, and Space Set to Level.
Occupancy Sensor Event - use the drop-down menu to set the event Action that will take place when occupancy is detected. Additional menu options will display based on the Action selected (e.g., if the Action is set to Preset Active, Preset Number and Timing (in seconds) displays for specification).
- Available actions include No Function, Preset Activate, Zone Set to Level, and Space Set to Level.

Configuration Sharing

Five buttons are available at the bottom of the configuration screen.

Note: Share is only available in the EchoAccess Mobile App.